Cleaning Instructions for BUNN My Café® Single Cup Pod Brewers
|
ROUTINE CLEANING
Before beginning any cleaning procedure, unplug the brewer to avoid the accidental start of a brew cycle. Clean the pod holder, drip tray and drip tray grate after each use, using a damp cloth and mild detergent and rinse. With the pod holder and drip tray removed, use a damp cloth with mild detergent to wipe the area below the pod holder and into the drip tray area. Occasionally, wipe the outside of the brewer with a damp cloth. (The reservoir, slide lid, pod holder, drip tray and drip tray grate are dishwasher safe.) |
 |
| PERIODIC CLEANING/DESCALING (Recommended At Least Once a Month.)
Periodically, you should clean and descale the brewer to clear any mineral deposits that may have accumulated due to impurities in the water source. If these deposits are not removed, they can impair the operation of the brewer and reduce the product life. There are several products available specifically for descaling. We recommend using URNEX® Activated Descaler or JavaClean2 Cleaner and Descaler, available on our web site. (White vinegar can be used to descale if a descaling product is not available.) Follow the directions as printed on the manufacturer’s package.
|
|
1.
|
 |
Fill the reservoir with descaling product as described by the manufacturer’s directions, or 1 quart (32 oz.) of white vinegar. Do not add powder mix directly to the reservoir. Descaling product must be mixed into a solution before it is added to the reservoir). |
|
2.
|
|
Place an empty pod holder into the brewer. Be sure the holder is locked into place, and set the VOLUME CONTROL SLIDE LEVER to the maximum position. (12 oz.) |
|
3.
|
|
Place an empty cup or bowl on the drip tray grate that will hold at least 14 oz. of liquid, and press the COFFEE BREW BUTTON to start a brew cycle. |
|
4.
|
|
Once the brew cycle has finished, empty the cup and set it back onto the drip tray grate. Press the COFFEE BREW BUTTON again to start a second brew cycle. |
|
5.
|
|
Once the brew cycle has finished, empty the cup and the remaining solution, or vinegar from the reservoir. Remove the Pod Holder; clean the reservoir and pod holder thoroughly using a mild detergent, then rinse. |
|
|
NOTE: There is now descaling solution in the internal tank. Follow the manufacturer’s directions if the solution must be left in the tank for any period of time. For vinegar, allow the solution to sit for at least two, but no more that four hours. |
| 6. |
|
Fill the reservoir to the maximum line with fresh clean cold water and place the pod holder back into the brewer. |
| 7. |
|
Place the empty cup or bowl back onto the drip tray grate and press the COFFEE BREW BUTTON to begin a brew cycle. |
| 8. |
|
When the cycle has finished, empty the cup. Repeat step 7 at least two more times to remove the solution from the tank. |
| 9. |
|
Clean the pod holder with a mild detergent and rinse thoroughly. |
| 10. |
|
Proceed to the “Cleaning The Sprayhead/Seal” section. |
|
|
| CLEANING THE SPRAYHEAD / SEAL |
|
1.
|
|
Press the Power Switch into the off “O” position. |
|
2.
|
|
Unplug the brewer and allow it to cool down. (Minimum of 1 hour.) |
|
3.
|
|
After the unit has been allowed to cool, remove the pod holder and set aside. |
|
4.
|
|
Using your fingers, rotate the sprayhead/seal assembly clockwise until the sprayhead and seal are removed. |
|
|
NOTE: If the sprayhead and seal are separated, they must be reassembled as they were when removed from the brewer.
NOTE: See “Assembling Sprayhead/Seal” and “Inspecting Sprayhead Seal” located further down page for more information. |
|
5.
|
|
Clean the sprayhead and seal with a mild detergent and rinse thoroughly. |
|
6.
|
|
Using your fingers, rotate the sprayhead/seal assembly counter-clockwise until it is finger tight. |
|
7.
|
|
Replace the pod holder. |
|
8.
|
|
Plug in the brewer and press the POWER SWITCH to restore power to the brewer. |
|
10.
|
|
Place decanter on base plate and plug in the brewer. Allow the water in the tank to reach brewing temperature before using (approximately 15 minutes). |
|
|
| ASSEMBLING THE SPRAYHEAD / SEAL |
| If the sprayhead and seal are separated during removal or cleaning, they must be reassembled properly. |
|
1.
|
|
Identify the top of the seal. The top of the seal that seats against the roof of the sprayhead ramp has a rough ridge that can be felt by running your fingers across the surface of the seal. The bottom is smooth. |
|
2.
|
|
Identify the top of the sprayhead. The top of the sprayhead has a star pattern and a threaded hole where the sprayhead attaches to the brewer. |
|
3.
|
|
While carefully stretching the seal, guide the sprayhead into the channel of the seal. Make sure it is completely in the channel. |
|
| When properly assembled, the sprayhead will slide easily into the channel of the seal and will not cause any buckles in the surface of the seal. If the sprayhead seems to be difficult to seat, and you must stretch the seal more than a slight tug, the assembly is not together correctly.
|
|
INSPECTING THE SPRAYHEAD SEAL
When disassembling your brewer for cleaning, inspect the sprayhead seal for cracks, tears and holes. Although the seal should last for an extended period of time, damage can occur through handling.
Replace the seal if it becomes damaged. This part is available to order online.
|
|
CLEANING THE POD HOLDER
To prevent residue build up, it is a good idea to periodically disassemble the pod holder/screen assembly and clean it with a mild detergent. |
|
1.
|
|
Press and hold the POD RELEASE BUTTON while sliding the pod holder out. |
|
2.
|
|
Flip the POD HOLDER upside down and place the holder cavity over the palm of your hand. |
|
3.
|
|
Using a small object, press the tab of the POD HOLDER INSERT through the hole in the bottom of the pod holder to remove. |
|
4.
|
|
Clean the screen and holder using a mild detergent and rinse. (Dishwasher Safe) |
|
5.
|
|
Press the insert back through the hole in the bottom of the POD HOLDER. |
|
|
CYCLING THE BREWER
If the brewer has not been used for an extended period of time, it is a good idea to cycle your brewer before brewing a cup of coffee or tea. |
|
1.
|
|
Remove the reservoir and pod holder from the brewer, clean with a mild detergent and rinse. |
|
2.
|
|
Refill the reservoir to the maximum line. |
|
3.
|
|
Insert an empty pod holder into the brewer. |
|
4.
|
|
Set the volume control lever to the maximum setting. |
|
5.
|
|
Place a bowl or cup on the drip tray grate that will hold at least 14 oz. |
| 6. |
|
Press the coffee brew button. |
| 7. |
|
When the brew cycle has ended and water drip out has stopped, carefully remove the pod holder and remove any excess water. |
|
You are now ready to brew. |
|
STORING THE BREWER
Unplug the brewer and wait for it to cool. If your Pod brewer has been used, it must be stored above 32ºF / 0ºC to prevent damage to the internal water tank. Empty and dry the water reservoir before storing. |
| NOTE: Water will remain in the internal tank. If stored for an extended period of time, refer to “Cycling The Brewer” section above before using. |
|
|
|
|
 |
